not an issue, but sharing an alternate method for the bltouch wiring. #12
Comments
|
That's great! Thanks for sharing! |
|
you’re welcome, thanks for your work on the firmware, i’m planning to start testing it properly tomorrow on my mega-x
Will Stevenson
0416280085
…________________________________
From: Oliver Köster <[email protected]>
Sent: Sunday, August 23, 2020 10:57:34 PM
To: knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>
Cc: will-stevenson <[email protected]>; Author <[email protected]>
Subject: Re: [knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S] not an issue, but sharing an alternate method for the bltouch wiring. (#12)
That's great! Thanks for sharing!
I'll update the Manual with the alternative wiring. It's sad that the BLTouch 2-Pin connector does not fit out of the box, so you need to swap the connector from 3 pin to 3 pin so it fits on G1-G2-G3.
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub<#12 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AP7Y6BTEHCX5UHMVT5JTU2TSCEG35ANCNFSM4QIUPXYQ>.
|
|
Thank you! Uhm... the Mega X will get an updated version (1.1.4) at the end of the day. I still need to figure out what Acceleration-Settings I can use. It's a bit hard to do when you don't have a Mega X at home ;) |
|
cool. i’ll check it out. happy to run any tests you need to validate settings.
Will Stevenson
0416280085
…________________________________
From: Oliver Köster <[email protected]>
Sent: Sunday, August 23, 2020 11:08:41 PM
To: knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>
Cc: will-stevenson <[email protected]>; Author <[email protected]>
Subject: Re: [knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S] not an issue, but sharing an alternate method for the bltouch wiring. (#12)
Done: https://github.com/knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S/wiki/BLTouch-Installation-(english)#alternative-wiring
Thank you!
Uhm... the Mega X will get an updated version (1.1.4) at the end of the day. I still need to figure out what Acceleration-Settings I can use. It's a bit hard to do when you don't have a Mega X at home ;)
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub<#12 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AP7Y6BWPJSG3WTI4IY4V64TSCEIFTANCNFSM4QIUPXYQ>.
|
|
hey mate, i’ve got 1.1.3 going, haven’t really started printing yet, still going through calibration. I’ve also added your project on thingyverse as a remix to my remixed mk4 x-carriage for Mega-X. also, regarding the bl touch wiring, the G1-3 pins are a bit closer together than the standard dupont cables, so i’ve used single pins and swapped the two pin plug for two single plugs that I took from the extension cable that came in the kit.[Image.jpeg]
Will
…________________________________
From: Oliver Köster <[email protected]>
Sent: Monday, August 24, 2020 6:10:56 AM
To: knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>
Cc: will-stevenson <[email protected]>; Author <[email protected]>
Subject: Re: [knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S] not an issue, but sharing an alternate method for the bltouch wiring. (#12)
Closed #12<#12>.
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub<#12 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AP7Y6BVIDXDPJMUTOHV5LR3SCFZVBANCNFSM4QIUPXYQ>.
|
|
it will probably fit a 3-pin JST plug ... as the G2 pin is 12v, i have considered using this to wire in a small LED strip, so might change it out and make a splitter cable with a 3 pin JST on the board that allows me to share the GND with the LED and BLtouch
Will
…________________________________
From: Will Stevenson <[email protected]>
Sent: Monday, August 24, 2020 6:33:10 PM
To: knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>; knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>
Cc: Author <[email protected]>
Subject: Re: [knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S] not an issue, but sharing an alternate method for the bltouch wiring. (#12)
hey mate, i’ve got 1.1.3 going, haven’t really started printing yet, still going through calibration. I’ve also added your project on thingyverse as a remix to my remixed mk4 x-carriage for Mega-X. also, regarding the bl touch wiring, the G1-3 pins are a bit closer together than the standard dupont cables, so i’ve used single pins and swapped the two pin plug for two single plugs that I took from the extension cable that came in the kit.[Image.jpeg]
Will
________________________________
From: Oliver Köster <[email protected]>
Sent: Monday, August 24, 2020 6:10:56 AM
To: knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S <[email protected]>
Cc: will-stevenson <[email protected]>; Author <[email protected]>
Subject: Re: [knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S] not an issue, but sharing an alternate method for the bltouch wiring. (#12)
Closed #12<#12>.
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub<#12 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AP7Y6BVIDXDPJMUTOHV5LR3SCFZVBANCNFSM4QIUPXYQ>.
|
|
This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs. |
Sign up for free
to subscribe to this conversation on GitHub.
Already have an account?
Sign in.
solder a bridge between the H3 and H4 pads, solder pins to G1 and G3 instead of to the bottom of B5 and B6. I have found this to be a much cleaner install.
The text was updated successfully, but these errors were encountered: